(The company recommends applying Tempaper with a squeegee, to reduce the chance of any lifting and bubbling.) We still think Tempaper is a decent choice, especially if you want lots of styles to choose from (there are 265 patterns, a number of which are collaborations with designers). But we subtracted points for ease of application, as well as the fact that one of the panels we applied in the kitchen lifted in one corner after a couple of very hot weeks (though this may be because it was located a couple feet from a stove). Once installed, the samples we tested did not have the cheap, plasticky look of contact paper, as some vinyl wallpapers can. If you want a wallpaper that you can view in a store before buying: Tempaper, a vinyl peel-and-stick option that came close to making our list of picks, is widely available at brick-and-mortar retailers, as well as online, so you can check it out in person. The patterns we tested were Baby Blue Lemons wallpaper, Sunny Delicate Scallop Print wallpaper in Yolk & Off White, and Greek Terrazzo wallpaper in Multicolor. This paper is also pricier than our two main picks, but we think the quality is worth it. And this one can be especially hard because of its thinness and strong adhesive you may want to consider calling a capable friend or hiring someone to help. All wallpapers can be relatively tricky to install by yourself. This quality might also make it more likely that the wallpaper could peel paint in rooms with intense climatic conditions (rooms that get very hot or very humid) or with older paint. But the strong hold also makes it harder to correct mistakes during installation, compared with other papers we tested. The adhesive has a very strong hold, which all but guarantees the wallpaper will stay up for years to come. It is the only textile-based peel-and-stick wallpaper we tested that is Oeko-Tex–certified, which may give some people peace of mind. Its fine-webbed, non-vinyl woven material is extremely lightweight and has a refined, matte look once installed. Both are manufactured by Minwax.We were impressed by Livette’s Wallpaper’s excellent print quality and designs in more than 300 patterns. To secure the face of the cabinet to the base, Tom and Kevin used wood glue by Gorilla Glue.įor the finish, Tom first applied a Pre-Stain wood conditioner, then a gel stain in Walnut. To cut all the boards to the proper dimensions and assemble the cabinet, Tom used a variety of tools, including a Domino Joiner, a Kapex KS120 sliding compound miter saw and a TS 55 circular saw, which are all manufactured by Festool. Tom and Kevin built the record player stand out of 3/4″ oak plywood and 1×4″ and 1×3″ red oak, which can be found at home centers. Attach the legs to the base of the cabinet using the provided hardware and a drill.In this case, Tom needed four coats to ensure a smooth, even finish. Allow each coat to dry before applying the next coat.Apply it with a brush and then wipe off the excess with a rag. Apply a wood conditioner to the box using a paintbrush.Wipe off the excess dust from sanding with a tack cloth.Start with 100 grit and work up to 220 grit sandpaper. Sand everything using the circular sander.Cut the molding to size on the miter saw to fit around the edges of the box and miter the corners.Cut the 1×4 inch red oak to size so it will fit inside the box towards the top and attach it to the box using the same floating tenon system.Clamp the box together and give it about half an hour to set up.Assemble the box using the floating tenons, wood glue, and a hammer.Then, angle the mortising drill to 45 degrees and drill mortises for the floating tenons at an angle. Hold the boards together where the miters come together and mark both sides with a pencil.Once all the pieces are cut, flip the board upside down and make the opposing 45 degree cuts.Then, cut one side of each panel where it was marked. Using a router, round off the front edge of the oak and make a rabbet cut on the back end of the panel.Run the board through the table saw to get the front piece of the oak to the correct dimension.Attach the 1×3 inch oak to the front of the plywood using a mortising drill, floating tenons, and wood glue. For now, work on the piece as one giant board instead of cutting the sides out individually.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |